Air conditioner for SD23 bulldozer spare parts
|Payment Type:||L/C,T/T,D/P,Paypal,Money Gram,Western Union|
|Terms of Trade:||FOB,CFR,CIF,EXW,CPT,CIP|
|Min. Order:||1 Piece/Pieces|
|Delivery Time:||1 Days|
|Place of Origin:||CHINA|
|Supply Ability:||1000 Pc per day|
Model No.: 23Y-58D-11000
air conditioner for SD23 bulldozer spare parts
The air conditioner is the Air Conditioner. Refers to equipment that uses artificial means to adjust and control the temperature, humidity, flow rate and other parameters of the ambient air in a building or structure.
Generally, it includes cold source/heat source equipment, cold and hot medium transmission and distribution system, terminal equipment and other auxiliary equipment. It mainly includes refrigeration host, water pump, fan and piping system. The terminal device is responsible for using the heat and cold from the transmission and distribution to specifically process the air condition so that the air parameters of the target environment meet certain requirements.
The structure of the air conditioner includes: compressor, condenser, evaporator, four-way valve, one-way valve capillary assembly, etc.
The working process of a tooth-tooth volume pair specified in an air-conditioning compressor. The gas on the side of the female screw and the male screw turning to cater to each other is compressed, and this side is called the high pressure zone; on the contrary, the side of the screw turning away from each other, the volume between the teeth is expanding and in the suction stage, which is called the low pressure zone. These two areas are separated by the contact line between the tooth surfaces of the female screw and the male screw. It can be approximated that the plane of the two screw axes is the boundary between the high and low pressure zones.
Compressed refrigerant (such as Freon) becomes liquid. Then use the heat absorption phenomenon when the liquid becomes gaseous under normal pressure for cooling.
The air density is very small. You take a needle tube for injection. Fill a needle tube with air, block the air outlet with your hand, and push the needle tube to compress the air. With a needle, the gas can be compressed by a third of its volume.
The compressor sucks in the lower-pressure working fluid vapor from the evaporator, increases the pressure, and sends it to the condenser, where it is condensed into a higher-pressure liquid. After being throttled by the throttle valve, the pressure becomes higher. After the low liquid, it is sent to the evaporator, where it absorbs heat and evaporates to become a lower pressure vapor, thereby completing the refrigeration cycle. For some applications, the gas must pass through a long tube (usually coiled into a solenoid) to allow the heat to escape to the surrounding air. Thermally conductive metals such as copper are often used to transport vapor. In order to improve the efficiency of the condenser, fins are often added to the pipeline to accelerate heat dissipation. The heat sink is a flat plate made of metal with good thermal conductivity.
The evaporator is inside the indoor unit, composed of pipes and covered with fins. A device that concentrates a solution or separates crystal grains from a solution by heating. It is mainly composed of heating chamber and evaporation chamber. The heating chamber provides the heat needed for evaporation to the liquid to promote the boiling and vaporization of the liquid; the evaporation chamber completely separates the gas and liquid phases. The vapor generated in the heating chamber contains a large amount of liquid foam. After reaching the evaporation chamber of a larger space, these liquids can be separated from the vapor by self-condensation or defoamer.
Shandong Tianfu International Trade Co.,Ltd.
Wheel Loader full spare patrs including: XCMG,LIUGONG,SDLG,LONKING ,SEM,XGMA,CHENG GONG ,SHANTUI,FOTON LOVOL ,DOOSAN, etc. Spare parts of each system including:Diesel engine system(Weichai,Shangchai,Xichai,DEUTZ),torque converter system,transmissoin system,transmission control system,axle system,implement hydraulic system,steering system,foot and hand brake system,front frame,tank,cab group,cover system,air conditioner system,electric system , etc. Wheel Loader Multi-function Auxiliaries :Wood grabber, pipe grabber, cotton grabber, grass grabber, sweeper, marble fork, snow shovel, snow thrower, ditch opener, etc.
- Company Name: Shandong Tianfu International Trade Co.,Ltd.
- Representative: Hongxin Gao
- Product/Service: Loader Parts , Road Roller Parts , Wheel Loader Parts , Excavator Parts , Bulldozer Parts , Auto Parts
- Capital (Million US $): 10000000RMB
- Year Established: 2019
- Total Annual Sales Volume (Million US $): Below US$1 Million
- Export Percentage: 61% - 70%
- Total Annual Purchase Volume (Million US $): Below US$1 Million
- No. of Production Lines: 4
- No. of R&D Staff: Fewer than 5 People
- No. of QC Staff: 5 -10 People
- OEM Services Provided: yes
- Factory Size (Sq.meters): Below 1,000 square meters
- Factory Location: 2-2-101, Sanjian Ruijingyuan, No. 3 Lanxiang Middle Road, Tianqiao District
- Contact Person: Mr. Hongxin Gao
- Tel: 0086-531-82793636
Premium Related Products